CNC Mach3 USB Hand Wheel 4 Axis USB HandWheel Pulse 50PPR Optical Encoder Generator MPG Pendant

CNC Mach3 USB Hand Wheel 4 Axis USB HandWheel Pulse 50PPR Optical Encoder Generator MPG Pendant
  • Продавецflimmer.com
  • Список ценUS $89.09piece
  • Продажная ценаUS $89.09piece
  • ДоставкаБесплатная доставка
  • Рейтинги3,5 (119)

Oписание продукта

LCD Display:
Axis Position display: +/-000.00mm to +/-999.99mm
Or in inch mode +/-00.000 to +/-99.999 inch
Button:
X/ESC:
a) Press and release to set as X axis control.
b) Press and release to escape or back to normal
c) Press and hold to set X ROLLING mode
Y/<:
a) Press and release to set as Y axis control.
b) Left direction button at Memory mode
c) Press and hold to set Y ROLLING mode
Z/>:
a) Press and release to set as Z axis control.
b) Right direction button at Memory mode
c) Press and hold to set Z ROLLING mode
A/Ent:
a) Press and release to set as A axis control.
b) Confirm button in Memory mode
c) Press and hold to set A ROLLING mode
Zero:
a) Press and release to set current position as zero
Back to Zero:
a) Press and release and all axis motor will move back to zero position
Divide to half: (HC mode only)
a) Motor will move to the current position/2, for example now is 10.00mm position of X.
then X axis will then move to 5.00 mm position

PC/ HC mode:

PC is computer controlling; HC is Hand wheel Controller mode.

LCD will display “PC Mode” or “HC Mode.

During “PC Mode” hand wheel control axis stepper motor function will be prohibited.

Memory and Emergency Stop function is allowed in both controlling mode.



Memory:

a) SAVE:

In normal operating mode, press and release “Mem” button to Memory mode.

Use “Y/<” and “Z/>” button to scroll the mode to SAVE -> MANUAL -> LOAD -> LOOP, and choose SAVE mode, press “A/Ent” to confirm the SAVE mode.

And then scroll the M0, M1, M2 or M3, this is 4 memory region, choose the target memory region and press “A/Ent” to start recording the motion



b) LOAD:

Looping mode will repeat to load the selected memory region.

In normal operating mode, press and release “Mem” button to Memory mode.

Use “Y/<” and “Z/>” button to scroll the mode to SAVE -> MANUAL -> LOAD -> LOOP, and choose LOAD mode, press “A/Ent” to confirm the LOAD mode.

And then scroll the M0, M1, M2 or M3, this is 4 memory region, choose the target memory region and press “A/Ent” to load the recorded region.



c) LOOP:

Looping mode will repeat to load the selected memory region.

In normal operating mode, press and release “Mem” button to Memory mode.

Use “Y/<” and “Z/>” button to scroll the mode to SAVE -> MANUAL -> LOAD -> LOOP, and choose LOOP mode, press “A/Ent” to confirm the LOOP mode.

And then scroll the M0, M1, M2 or M3, this is 4 memory region, choose the target memory region and press “A/Ent” to start looping the recorded region.

Can press “X/Esc” and go back to normal operating mode.



d) MANUAL:

Can press “X/Esc” and go back to normal manual operating mode.



Emergency Stop:

Will enter emergency stop mode:

1) Press “EMERGENCY” in MACH3

2) Press “ESTOP” in hand wheel controller

3) Spindle motor overcurrent or abnormal situation is detected

4) Limit switch is triggered



LCD will show “ESTOP” once it is triggered.



While emergency stop, spindle motor, all stepper motors will be stopped.

Buzzer inside the main controller box will beep.

*not recommend to use emergency as stop function; motor will be stopped without normal deceleration. This will reduce the life of motors and mechanical structure.



Can press again the ESTOP button in hand wheel controller and back to normal



Divide to half:

It is usually to use for finding the center of the material,

Go to point 1 press zero and then go to point2, press divide to half, and then the bit will go to center.

Be careful that you will need to move the Z axis up by yourself to avoid crash.



Back to Zero:

Press and hold the “SPEED” button for 3 seconds.

All axis motor will move back to the zero point according the hand wheel’s zero display

*Position on hand wheel and Mach3 is not correlated. If you need to move back according MACH3 position, you need to press back to zero in MACH3



Rolling:

Press and hold the “X”, “Y”, “Z”, “A” button for 3 second, LCD will display “R” in corresponding axis.

The axis stepper motor will move forever in constant speed. There are 4 speed selections by press and release the “Speed” button.

Can control clockwise, counter-clockwise or stop by rotate the hand wheel, rotate counter-clockwise 1 step to have counter-clockwise rotation, rotate hand wheel one step clockwise to stop, etc.



Limit Switch:

At X, Y, Z axis, are installed 2 mechanical limit switch on both side. Once it is triggered, controller will send out limit switch triggered signal to PC and whole system.

The triggered axis will drive back around 5mm immediately; this action can prevent crash, accident on human and release the limit switch.

*Reset the zero position is necessary once limit switch is triggered.

Include

1 x Handwheel